Lift the grime, then refill every joint with sand
Paver Cleaning and Joint Sand in Arlington, FL
Get green, dull Arlington pavers washed and re-sanded, starting with a free estimate at (904) 944-6930.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Can I get my Arlington pavers cleaned soon?
A local contractor cleans pavers across Arlington, FL, and you will hear back within 1 business day, usually much sooner. New joint sand is part of the job, and the free estimate comes with no pressure to book. To start, call (904) 944-6930.
Cleaning removes the algae, tannin marks, rust and grime that dull pavers, so the surface looks brighter and grips better underfoot. Fresh sand then fills the joints, which steadies the pavers and leaves weeds little room. The back walk under the oak that went dark over the summer can match the rest of the yard again. Point out the worst spots when you ask for your free estimate.
Paver Sealing Arlington Is Proud to Serve Northeast Florida
- Arlington Hills
- Southside
- Brentwood
- San Marco
- Fort Caroline
- Sandalwood
- Royal Terrace
- Panama Park
- San Jose
- San Pablo
- Riverside
- Paxon
- Beauclerc
- Cedar Hills
- Atlantic Beach
- Oceanway
- Highlands
- Jacksonville Beach
- Baymeadows
- Mandarin
- Argyle Forest
- Ponte Vedra Beach
- Bellair-Meadowbrook Terrace
- Palm Valley
- Dinsmore
- Whitehouse
- Fruit Cove
- Lakeside
- Fleming Island
What is part of a paver cleaning job?
The job runs from stain treatment to a gentle wash, then new joint sand after the pavers dry. You can book it alone, or as the first stage of a sealing job. Walks under oaks and spots near sprinkler heads usually take the most time. To line up a cleaning, call (904) 944-6930.
Stain treatment
A cleaner matched to the problem, whether algae, rust, oil or tannin, goes on first and is tried on a small spot.
Gentle wash
A surface cleaner covers the area evenly without blasting sand out of the joints.
Fresh joint sand
Dry sand is swept into every gap once the pavers have dried, then settled.
Sealer if you want it
A sealer coat is the optional last stage, applied only after the pavers have fully dried. The sealing guide covers what it adds.
What are the signs my pavers need cleaning?
Signs include a green or black film on shaded edges, brown stains under an oak, orange marks near a sprinkler head, weeds in the joints and sand on the driveway after rain. Algae matters most on a pool deck or front walk, since a slick surface is a fall risk. To have yours looked at, call (904) 944-6930.
Is cleaning enough, or should I seal too?
A cleaning fixes how the pavers look today, and a coat of sealer decides how long that look lasts. Stopping at a cleaning costs less now, but algae, rust and fading come back on their own timetable. With a coat in place the next wash goes faster, but the coat itself needs redoing every few years. Say which you want when you ask for your free estimate.
How often should Arlington pavers be cleaned?
Once a year suits many homes, and shaded sides may want attention sooner. Moisture collects on the north and east sides of a house in this part of Duval County, and algae follows. An open driveway can go longer. To build a routine around your yard, call (904) 944-6930.
Does a harder blast clean pavers better?
No. Western Interlock, a paver company, keeps pressure near 2000 PSI or less, because higher pressure can strip the surface of some pavers. Unilock says to spray at a low angle, no greater than 30 degrees, so the sand stays put. Ask what pressure and tip the contractor uses when you ask for your free estimate.
Even results come from a surface cleaner kept at one height, with a stain remover chosen for each mark doing the hard work. Ask where the rinse water goes, too, especially if your yard slopes toward a pond or storm drain. To ask those questions now, call (904) 944-6930.
Why do live oaks leave brown marks on my pavers?
Oak leaves carry tannins, and wet leaves left on pavers pass those tannins into the surface. An exterior cleaning company that serves Arlington reports brown water stains on drives and walks beneath live oak canopy. Western Interlock, a paver company, makes the same link between leaf stains and tannins. Sweeping often helps, and a cleaner made for organic stains lifts what is left. To plan a cleaning, call (904) 944-6930.
What is the orange staining near my sprinklers?
Most often it is iron in the water. The same exterior cleaning company says iron in irrigation water leaves orange marks on drives, garage doors and stucco, and that more pressure makes them worse. A rust treatment lifts them, and they have to be gone before any sealer goes on. Point them out when you ask for your free estimate.
Why is there a white film on newer pavers?
A chalky white film on newer pavers is usually efflorescence, a mineral deposit that often fades on its own. Unilock says it typically takes two to three months and can take up to a year, and sealing should wait until it is gone. Sealer that has clouded over can resemble it. Point the contractor to the spot when you call (904) 944-6930.
Which paved areas can be cleaned at an Arlington home?
Every paved area at the house can be cleaned, from the drive and pool deck to the patio and front walk. Each one collects its own kind of grime, so cleaner and method vary. To start with yours, ask for your free estimate.
Driveways
Tires, oil drips and hours of sun land on the driveway first. Cleaning a long drive keeps the color even from the street to the garage.
Pool decks and lanais
Pool decks take splashes, chlorine and bare feet every day. Cleaning one inside a screened cage should leave it gripping, not slick.
Back patios under oaks
Patios in oak shade stay damp and collect leaves, so green growth and brown tannin marks start early. These areas usually take the most scrubbing.
Walkways and entries
Walks pick up soil, mulch and irrigation overspray along the edges. Cleaning the front walk is a small job every visitor notices.
What makes Arlington pavers dirty?
Oak tannins, shaded algae, lost sand, irrigation rust and sun wear lead the list. Cleaning handles several of them, and sealing or repairs handle the rest. To learn which of these fit your home, call (904) 944-6930.
1. Brown marks under live oaks
An exterior cleaning company that works in Arlington reports brown water stains on drives and walks under live oak canopy. Leaves left on wet pavers add to it, since the stain comes from tannins.
2. Green growth on shaded sides
Duval County sits in a humid subtropical belt, and the same company says moisture collects on the north and east sides of a home. Afternoon storms in summer keep algae fed.
3. Joint sand running out
Summer storms pull sand from pool decks and driveways. Once joints run low, pavers start to move and weeds come back, so sand is refilled before any coat goes down.
4. Orange irrigation rust
Iron in sprinkler water leaves orange marks near the heads and along edges. A rust treatment lifts them, and more pressure only makes them worse.
5. Sun and chlorine wear
An open driveway or a pool deck takes the hardest hits. A wash shows how much color remains, and a coat after it helps keep that color.
What does paver cleaning cost in Arlington?
Stallone's Pro Wash, a Duval County paver company, lists cleaning from $0.22 per square foot, with the final price set by square footage, paver type and whether joint sand is needed. That puts a 600 square foot driveway near $132 and a 1,000 square foot pool deck near $220. A 2026 Duval County price guide puts new joint sand at another $0.25 to $0.75 per square foot. For a price on your property, ask for your free estimate.
If sealing is part of the plan, ask for a combined price. The published going rate for the whole clean, sand and seal is $1.75 to $3.25 per square foot. To weigh the two options, call (904) 944-6930.
Want the surface protected as well? The paver sealing guide covers that, and the paver sealing in Arlington home page gives the overview.
| Paved area | Cleaning from | Full clean, sand and seal |
|---|---|---|
| 700 sq ft | $154 | $1,225 to $2,275 |
| 1,100 sq ft | $242 | $1,925 to $3,575 |
| 1,700 sq ft | $374 | $2,975 to $5,525 |
The cleaning column multiplies the $0.22 per square foot starting rate that one Duval County paver company lists. The last column uses the $1.75 to $3.25 per square foot another local company published, read in November 2026. Larger areas often cost less per foot, and the quote for your home may differ.
Why use a local contractor to clean pavers in Arlington?
A contractor who works east of the river knows what oak leaves, sprinkler iron and damp north sides leave behind. Compare the quote with the published rates here, then decide when you are ready. To begin, ask for your free estimate.
Contractors who know Arlington
A company that works east of the river deals with the same live oaks, humidity and afternoon storms your pavers do. The first visit then starts with real knowledge of the area.
A free look and a free number
The estimate costs nothing, and you are free to say no. Pavers are your call, from the finish to the date.
Published rates to compare
Local companies post what they charge per square foot, and the ranges on this site come from those pages. If a quote lands far outside them, ask why.
Time to decide
Ask for the price in writing and take a few days if you want. That page lists what to check before you sign.
Want a free estimate to clean your Arlington pavers?
Use the form or phone, and a contractor responds within 1 business day, usually much sooner.
Free, no obligation
What do cleaned pavers look like around Arlington?
What is the paver cleaning process, step by step?
If sealer is skipped, the work ends at step four, when the joints are full. To set a date, call (904) 944-6930.
1. Look it over and measure
The contractor walks the area for the cleaning quote and notes dips, loose pavers, old sealer, stains and where water pools.
2. Wash with care
Sprinklers go off and plants get covered. A surface cleaner does the wash, since Western Interlock, a paver company, keeps pressure near 2000 PSI or less and Unilock sprays at a low angle so sand stays in the joints.
3. Treat the stains
Dirt and algae get soap or a paver cleaner and a soft brush, never a wire brush, which Unilock says leaves metal particles that rust. Oil is soaked up first, then lifted with an extractor.
4. Refill the joints
After the pavers dry, kiln dried sand is swept in and settled. Western Interlock notes that some sand washes out during cleaning, so there is always a little to add.
5. Seal and walk the job
When sealer is part of the job, it goes on dry pavers with a sprayer and a short pile roller, in one session so the gloss stays even. The contractor then walks you through how long to stay off.
Frequently Asked Questions
Can I pressure wash brick pavers?
Yes, at moderate pressure. Western Interlock, a paver company, keeps it near 2000 PSI or less and uses a surface washer for even results. Unilock says to spray at a low angle, no greater than 30 degrees, so sand stays in the joints. Plan to add sand afterward.
How do I remove oil stains from brick pavers?
Soak up fresh oil first. Unilock suggests paper towels or kitty litter, then soap and water or a driveway paver cleaner. For older stains, Western Interlock describes an oil extractor left on for about 10 minutes, then rinsed, repeated until the stain lifts.
Can I use Dawn dish soap to clean my pavers?
For dirt and algae, Unilock lists soap and water or a paver cleaner with a soft brush, and it names dish soap with a stiff plastic brush for efflorescence. Never a wire brush, because metal particles can leave rust marks. Rinse well and keep runoff away from plants.
How much does it cost to clean pavers?
Stallone's Pro Wash, a Duval County paver company, lists cleaning from $0.22 per square foot. A 700 square foot Arlington driveway would start near $154. The final price depends on square footage, paver type and whether joint sand is needed.
How much should I pay for paver sealing?
A fair quote usually sits inside $1.75 to $3.25 per square foot for the whole clean, sand and seal. A 2026 Duval County price guide warns that bids under $1 per square foot almost always skip prep. Ask what each number covers.
How much does it cost to seal outdoor pavers?
It depends mostly on size. At the published $1.75 to $3.25 per square foot, a 1,100 square foot driveway and patio together comes to about $1,925 to $3,575. Stripping failed sealer adds $0.75 to $1.50 per square foot.
How do I get rid of orange rust marks from my sprinklers?
Use a rust treatment made for pavers, not more pressure. A Duval County exterior cleaning company says iron in irrigation water leaves orange marks and that extra pressure makes them worse. The marks have to be gone before any sealer goes down.
Why do my Arlington pavers turn green on one side of the house?
Moisture collects on the north and east sides of a home in this humid subtropical county, and summer afternoon storms keep algae fed. Unilock suggests soap and a paver cleaner for algae, with white vinegar left on for 10 to 15 minutes for mildew.
Tired of green, stained pavers in Arlington?
Share your street and what needs washing, and a contractor will reply within 1 business day, usually much sooner, with a free estimate.
Free, no obligation